Solveeit Logo

Question

Question: Draw the circuit diagram of the voltage regulator using the Zener diode....

Draw the circuit diagram of the voltage regulator using the Zener diode.

Explanation

Solution

Zener diode is a type of a diode which is doped properly to give the sharp breakdown voltage. It can be used as a voltage regulator to maintain a constant voltage for the varying voltage provided by the source to the circuit. Here we will draw the circuit for the Zener diode when used as a voltage regulator.

Complete step-by-step solution:
A Zener diode is a diode, which works in a breakdown region and it is used in the reversed biased condition. Let us draw a reverse characteristic of the Zener diode for a better understanding.

As we can see that for the range IZmin to IZmax{{I}_{\text{Zmin}}}\text{ to }{{I}_{\text{Zmax}}} zener voltage is approximately constant and this region for which zener voltage is constant is the breakdown region. IZmin{{I}_{\text{Zmin}}} is also called knee voltage or we can say it is the minimum value of zener current whereas IZmax{{I}_{\text{Zmax}}} is the maximum value of zener current beyond this value the zener diode will burst. Therefore zener diode is used within the range of IZmin to IZmax{{I}_{\text{Zmin}}}\text{ to }{{I}_{\text{Zmax}}}.
Now, as Zener voltage remains the same for the range IZmin to IZmax{{I}_{\text{Zmin}}}\text{ to }{{I}_{\text{Zmax}}} it can be used as a voltage regulator when it is operated in the breakdown region. Because the work of a voltage regulator is to keep the output voltage the same for varying input. To understand how Zener diode works as a voltage regulator let us draw a circuit diagram for the voltage regulator using Zener diode.

Here we can see from the diagram, there are two resistors R and RL{{R}_{L}} where R is connected in series so as to absorb all the fluctuation of the output voltage and RL{{R}_{L}} is the load resistance across which output voltage is obtained. VZ{{V}_{Z}} is the Zener voltage and I1{{I}_{1}} is the current flowing through the circuit which divides into IZ{{I}_{Z}} and I2{{I}_{2}}. IZ{{I}_{Z}} is the Zener current flowing through the Zener diode and I2 is the current flowing through load RL.
Now if we apply Kirchhoff’s current law at node A we can write
I1=IZ+I2{{I}_{1}}={{I}_{Z}}+{{I}_{2}}
Now there can be two cases when the source is varying or input is varying and when the load resistance is varying. Let’s take the first case where input is varying, in this case, the extra voltage or the fluctuation is absorbed by series resistance R due to which total current or I1{{I}_{1}} will increase but this increase is balanced by Zener current IZ{{I}_{Z}} and so I2{{I}_{2}} doesn’t change resulting constant output voltage across load resistance.
In the second case that is when load resistance changes and input is fixed then there should be an increase in load currentI2{{I}_{2}}. As input is constant I1{{I}_{1}} remains the same and the change is compensated by Zener current IZ{{I}_{Z}}. For example, if load resistance decreases then load current should increase so that output remains the same, therefore Zener current decreases so as to provide the amount of current required at load resistance to keep the voltage constant ( because total current I1{{I}_{1}} remains constant).
Hence this way Zener diodes can be used as a voltage regulator.

Note: Zener diode is always reversed biased and the breakdown voltage or the Zener voltage depends on the doping of the diode. If the diode is lightly doped then the depletion layer will be thin and so we get a lower breakdown voltage. If the diode is heavily doped then the depletion region will be greater resulting in higher breakdown voltage. For voltage stabilizer, a heavily doped diode should be used, so as to get constant voltage over a large range of varying input voltage. Note that when the source voltage or input voltage is less than Zener voltage Zener diode works as an open circuit.